Flexovit emery cloth sanding sheets have an incredibly strong cloth backing for increased product strength and durability. Can be torn into strips for detailed work and is suitable for hand or power tool use. Ideal for removing rust, paint and scale from metal surfaces. The fine grits are also ideal for preparing and polishing metal. Size: 230 x 280mm.Grit: 150 (Very Fine).Pack quantity: 25.
IRWIN Vise-Grip Groovelock Waterpump Pliers have an all-purpose jaw that can grip onto flat, round, hex and square work pieces. The multi-groove ratcheting system has twice the number of groove positions compared to traditional groove joint pliers. A press-n-slide button adjusts the jaws twice as fast as traditional groove joint pliers. Anti-pinch non-slip grips provide control, comfort, and less hand fatigue.These Irwin ;Vise-Grip Groovelock Waterpump Pliers have the following specifications: Capacity: 114mm.Length: 400mm (16in).
Lockfast Woodstock drain, chimney and flue brush, has a wooden stock, brass joint and polypropylene bristles. For brick chimneys and coal burning applications, and drain cleaning purposes.Size 200mm (8 in).
Irwin Junior Saw has a large contoured handle and the blade tensioning screw provides more control and better performance than a standard junior hacksaw. Size: 150mm (6in).
The Wera BiTorsion Extra Hard (BTH) bits significantly extend service life. Ideal for use with screws into general construction materials and timbers. Use with Wera BiTorsion Rapidaptor bit holder for ultimate service life. Use with all combi and drill drivers. For impact tools, use Impaktor bits.Card of 2 Wera 855/1 BTH BiTorsion Pozidriv PZ2 Insert Bit Extra Hard 25mm
Stick Nails for use with the Stanley Bostitch Wire Weld Framing Nailers, the traditional wire weld collation gives the stick nails more rigidity and resistance to damp environments. 28° Collation Angle Designed for the construction market, where it is important to find the right combination of tool weight and working autonomy. Since sticks contain fewer nails than coiled nails (approx 25) and less of them are loaded into the nailer, the tool is lighter. A simpler feed mechanism for stick nails also helps to keep the weight of the tools lower than for coil nailers for similar size nails. This is important when you are working up a ladder with your arm stretched out. (Remember only tools fitted with sequential trip should be used when working up a ladder). Smooth shank nails have exactly that: a smooth appearance. Due to their regular form they can be produced at very high speed and are therefore the most economical type of nail. However, their holding power is the lower than ring shank nails. They require less energy to drive them and the air consumption per nail can be lower. Sometimes it is possible to use a smaller tool to drive them. Ring shank nails have a series of rings punched into the surface of the shank. Again a difference in the diameter of the shank is produced making it even more difficult to withdraw the nail. Ring shank nails have to be produced at lower speeds and their cost is generally higher than for a smooth shank nail. The air consumption per nail is also higher, and the energy required to drive these nails into hard wood is very much greater. Bright finish is without any form of protection and is the most economical choice, but the nails will start to rust before nails that have a protective treatment. Used in applications where no protection is required, for example a one way disposal pallet. As all standard nails come with this finish. Galvanising , or coating with Zinc, is the best way to prevent nails from corroding. The zinc does not protect the steel of the nail, but is corroded first. The thicker the zinc coating, the longer it will be before the nail is attacked. The thickest coating is called hot dipped and is applied by dipping the nails into a bath of molten zinc. Galvanised protection is measured in Microns (each Micron is 0.000001 of an metre thick). The thicker the micron coating the better the protection level of the nails.Gauge/Diameter (mm) 3.1 Length 90 28° Collation AngleSKU S310R90 Profile RING Finish BRIGHT Description STICK NAIL 3.10-90 RING 2M Qty per box 2000Will also fit the N80SB, FW28WW-E, N100S
These Forgefix single threaded Decking Screws have Pozidriv heads and are specially designed, hardened and green treated. The design of the screw helps prevent splitting the boards, and allowing them to expand and contract with the changing seasons. APPLICATIONSpecifically used in Decking applications but also widely used in exterior timber and fencing applications. The 1,000 hour green treated finish offers excellent corrosion resistance to ACQ (Alkaline Copper Quaternary) treated timber used in construction and decking applications. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Single thread screws have been designed to offer higher pull out values and quicker insertion.Decking Screw Pozi ST Green Anti-Corrosion Treated 4.5 x 75mm Bulk 1000
