Irwin Visegrip 9LNC Long Nose Locking Plier 225mm 9in

100 Series hasp and staple with concealed hinge pin and concealed screw heads, corrosion protected. Only the carded versions include fixings. 100/80 and 100/100 have hardened steel staples. Where to use it: Designed for doors closing flush, i.e. door leaf and door frame are level DG versions: with double joint designed for doors not closing flush, i.e. door leaf and door frame are not level, and corner solutions.Hasp length: 60mmHasp width: 20mmStaple bore dia: 7mm

The Lindstrom Supreme Oblique Cutting Nipper produced from high performance tool steel. It has a screw joint that minimises friction and alignment of cutting edges. The edges are precision induction hardened to 58-60 HRC. The handles with return spring and sleeved.Length (A): 108mm (4.25 in).Blade length (B): 8mm (0.31 in). Head width (C): 10.5mm (0.41 in). Head depth (G): 15mm (0.59 in). Cutting capacity: 0.35-1.25mm. Head type: Double angled. Cutting edge: Flush. Angled heads, also known as oblique style, are set at an angle to the main body of the cutter. This means that the cutter can reach between parts and areas which are difficult to access. The Flush Bevel cut is designed to meet the requirements of the electronic assembly industry. Leads are ‘pinched’, allowing less altitude and a smaller overall surface area – more than Micro-bevel cuts. The cutters have fine cutting edges that leave a narrow and short taper and small exposed area. They can be used to meet tight specifications for a flush result to a board, component or part.

Type:Faucet Light; Style:Contemporary; Finish:Plastic; Suitable Rooms:Bathroom; Features:LED; Net Weight:0.000

Traditional style white plastic dimmer switches.Available in 1 or 2 gang.1 Gang dimmer switch for loads up to 250 Watts

These Forgefix double slotted roofing bolts are supplied with square nuts and have a low profile mushroom head. Their bright zinc plated finish increases resistance to corrosion. The bolts are therefore suitable for both interior and exterior use, and can be exposed to weather conditions without the risk of rusting. APPLICATION:Used in many applications other than roofing, when joining products together.Use clearance drill sizes 1mm larger than bolt diameter. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. With slotted screwdrivers it is important to ensure that the tip matches the width of the screw slot, otherwise you run the risk of damaging the screw head. Slotted screwdrivers are available with either Flared or Parallel tips. For the majority of uses the Flared tip is ideal but if the screw/bolt needs to be driven below the material surface a Parallel tip screwdriver should be used.Roofing Bolt ZP M6 x 70 Bag 25

These Forgefix Pozidriv Self-Tapping Screws have countersunk heads and are Zinc Plated for increased resistance to corrosion. They tap their own thread in to a pre-drilled pilot hole in sheet or solid material. They are single threaded to resist pull-out. APPLICATION:Ideal for use in many DIY, ironmongery, engineering, electrical and plumbing applications. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. The Pozidriv screw is similar in appearance to the classic Phillips cross-head, but in fact is very different. The Pozidriv has four additional points of contact, and does not have the rounded corners that the Phillips screw drive has. The biggest advantage it offers is that, when used with the correct tooling in good condition, it does not cam out, allowing great torque to be applied. The Pozidriv screw can easily be distinguished by a line embossed in the screw head at 45° to the slots for the driver. Countersunk heads are designed to sink flush with substrates to leave a smooth surface finish.Self Tapping Screw Pozi Countersunk ZP 3/4 x 6 Box 200