The Wera BiTorsion Extra Hard (BTH) bits significantly extend service life. Ideal for use with screws into general construction materials and timbers. Use with Wera BiTorsion Rapidaptor bit holder for ultimate service life. Use with all combi and drill drivers. For impact tools, use Impaktor bits.Card of 2 Wera 855/1 BTH BiTorsion Pozidriv PZ2 Insert Bit Extra Hard 25mm
These Forgefix Screw Cup Washers have a solid brass finish to avoid corrosion. They are quick and easy to install, with no need to countersink screws. APPLICATION To enable flush finish in numerous joinery installations. Can be used with most screw types.Screw Cup Washers Brass No.8 Forge Pack 20
Designed for use with angle grinders with a compatible thread and are suitable for industrial use and more specialist applications. Twist knot wire brushes are suited to heavier duty applications such as the removal of slag, rust, scale or even dried concrete. Wire: High tensile twisted steel Type: CupFace Diameter: 100mmThread: M14 x 2Wire: 0.5mmConforms to ISO 9001 and DIN EN1083-1 and 2Maximum rpm 8500
These Forgefix Phillips, Single Coarse Thread (SCT) Drywall Screws have a black phosphate finish for increased durability. Their Bugle Head allows the screw to sink effortlessly into the dry lining without the need for countersinking, which in turn minimises the damage to the surface. They are supplied collated, with 50 screws per strip and 1,000 screws per box. APPLICATION:Designed for fitting dry lining to studding. Phosphate coatings are made up of thin crystalline layers of phosphate compounds that adhere to the surface of the fixing or fastener. The phosphate crystals are porous and can be formed from zinc, manganese, or iron phosphate solutions. Phosphate coatings offer good corrosion resistance and have an excellent ability to absorb supplementary coatings which improves appearance, corrosion resistance and resistance to abrasion. The Phillips screw has four simple tapered slots. It is designed so that a Phillips tip screwdriver can turn a screw with increasing torque. When the torque gets to be too strong for the tip then the screwdriver tip winds itself out of the screw thus preventing over-tightening and or damage to the screw head. Coarse thread screws (mainly drywall screws) have an extremely sharp point and are designed to penetrate plasterboard skin. The coarse thread eases in to the board then the timber baton holding the board firm.Drywall Collated Screw Phillips Bugle Head SCT 3.99 x 35mm Box 1000
Jubilee® clips are Kite marked to BS5315 (1991) and the company is licensed to ISO 9001. Made from mild steel, zinc protected and used for fixing flexible rubber hoses, metal tubes etc.Size 6XAdjustment . 120 - 150mmAdjustment. 4.3/4 - 5.7/8in
These Forgefix double slotted roofing bolts are supplied with square nuts and have a low profile mushroom head. Their bright zinc plated finish increases resistance to corrosion. The bolts are therefore suitable for both interior and exterior use, and can be exposed to weather conditions without the risk of rusting. APPLICATION:Used in many applications other than roofing, when joining products together.Use clearance drill sizes 1mm larger than bolt diameter. Zinc coatings prevent oxidation of the protected metal to create a longer lasting finish. It does this by forming a barrier and by acting as a sacrificial anode if this barrier is damaged. Zinc oxide is a fine white dust that (in contrast to iron oxide) does not trigger a breakdown of the substrate’s surface integrity as it is formed. The zinc oxide, if left intact, can act as a barrier to further oxidation, in a way similar to the protection afforded to aluminium and stainless steels by their oxide layers. With slotted screwdrivers it is important to ensure that the tip matches the width of the screw slot, otherwise you run the risk of damaging the screw head. Slotted screwdrivers are available with either Flared or Parallel tips. For the majority of uses the Flared tip is ideal but if the screw/bolt needs to be driven below the material surface a Parallel tip screwdriver should be used.Roofing Bolt ZP M6 x 70 Bag 25
The ALM Manufacturing Replacement Chainsaw Chains to fit a wide range of chainsaw makes and models.The ALMCH066 Chainsaw Chain has a 3/8 inch Low profile (L/P), 0.043in guidebar slot 0.325 mm and Low profile (L/P) 1.1 mm guidebar slot.This chain is made to fit the Ryobi range and suit saws with a 40cm bar and chain with 66 drive links including:PCN-3840, PCN-4040.
