MR. JUMP, the fiber helmet studied in details for comfort, technology and for sure safety for end user. It has been studied and tested to optimize the outside and inside air flows. OUTER SHELL in tricarboco material, mix of Kevlar, carbon and fibre, joint through resin hand made using new technologies, which foresee aramidic resins. 2 different shell sizes: XS-L and XL-2XL INTERNAL POLYSTYRENE protective lining, available in three sizes (S, M and L). The special shape and construction in different density increases mechanical resistance in the event of accidental shock. Inner channels studied in the wind tunnel guarantee a perfect ventilation. The D-RING RETENTION SYSTEM has been designed and patented by Suomy. Insert the free side of the strap in the rings. Pull the end until the strap presses firmly against the jaw. After this operation, it should not be possible to remove the helmet. Verify that by grabbing it from the back and rotating it to the front it cannot be removed and it is fixed to the head. If the helmet tends to come off or rotates freely, tighten the strap again until the right pressure is obtained and repeat test. If after repeating the test you are not able to efficiently tighten the retention system, do not use the helmet. Only after checking the correct tension of the strap, fix the free end locking it with the automatic stud to the release tab. The automatic stud is necessary only to fix the free end of the strap to prevent it from flapping while riding. Fixing the release button does not assure that the helmet is correctly in position and properly fastened: the correct locking of the strap must be verified exclusively following the above paragraphs. To release the retention system, release the automatic stud button and pull the release tab to loosen the closure. Slide out the free end of the strap from the «D Rings». Use the release tab only to remove the helmet! Never release this tab while riding. MRJUMP is homologated as per the following rules: ECE 22-05, DOT, JIS, INMETRO NBR 7471 CHEEK PADS completely removable and washable, with different thickness to get a perfect customization od the helmet. INTERNAL SHELL completely removable and washable, in different thicknesses for a complete customization of the product. The internal removable shell has been studied for an uniform stand on the head. The visible channels allow the air flow to check the temperature in the internal part of the helmet and to let off the hot air through the back part. INNER (cheek pads and inner liner) are completely in fabric COOLMAX® ACTIVE with treatment INTERPOWER: Wicks sweat away from the body. Keeps the user fresh, dry and comfortable. Lightweight, soft and breathable fabric. Performance verified and certified by ADVANSA. The SHELL is in polystyrene with channels for air flows. In the front part there are upper and back air ventilations, which help the internal helmet ventilation. On the CHIN GUARD there is an air ventilation for the front ventilation. The OUTER SHELL has ribs to channel better the air flows. The PEAK has an aereodynamic impact. The wide open space in the front allows the use of any kind of glasses. weigth: ca. 1000gr
Historic shapes and colors meet modern design. The Legends helmets immortalize riders and achievements that will never be forgotten. Comfort, protection and ventilation are key elements of these helmets that meet today’s highest standards. The X3000 carries Agostini’s signature and includes the contoured chin piece just as he liked it so that he could lean right up against the gas tank. It also features a dual button visor that can be opened with the left hand alone. The iconic piece that gave birth to the AGV logo: the tricolor Agostini helmet, seen from behind, just as his rivals saw it. Same shape, same color scheme, the same leather bag used to transport it, modern technology. Timeless allure in just 3000 limited pieces. Features Shell in Fiberglass engineered in 3 sizes, EPS structure developed in 3 sizes Visor on-off air vent with channels hollowed in the shell Premium interiors with Genuine leather, Suede fabric and Embroidered logo Fully removable and washable interiors (neck roll excluded) Anti-scratch visor with micro-opening system Double D retention system
MATERIALGewachste Cordura 500 w / a Hand gefertigte Behandlung Miporex Membran Baumwolle / Viskose-Twill-Futter abnehmbare weiche Protektoren an den Knien und Hüften innere Struktur: Herausnehmbares Steppfutter SCHUTZProtektoren mit der EU-Richtlinie 89/686 / EWG und der technische Norm EN 1621-1: 2012 TASCHENZwei Fronttaschen classic FEATURESVersiegelte Nähte Membran Wasserdichter Reissverschluß Reflex-Paspel am Unterschenkel GRÖSSEN: 44-46-48-50-52-54-56-58
Features Waterproof and breathable thanks to the soltoTEX® membrane Textile lining Comfort foot bed 2 zippers to make it easier to put on the boots Reinforced heel cap Stretch insert on the calf Inner boot with neoprene on the top for more comfort Reflective insert on the heel Plastic inlays on ankle and shin section Abrasion-proof rubber sole Gear lever protection made of rubber Safety: in accordance with the standard EN13634:2015
Features Collar made with corduroy With waterproof and breathable Reissa Z-liner membrane. The thermal lining can be removed at the zipper Small ventilation holes under the armpits The smocked fit on both sides gives a nicer fit and more comfort By the two zippers on the back of the sides, you can continue the jacket if necessary Certified protectors on shoulders and elbows A foam back pad incl., A certified protector for the back can be ordered separately. With belt loop to connect the jacket and pants with a belt 2 pockets outside and 2 inside
